Skip Navigation Website Accessibility
 

JL Audio FiX-86 OEM Integration DSP

   
Quantity:    
Notes:    

This item is not available for purchase online. Please call 610-788-2226 for more information.
JL Audio FiX-86 OEM Integration DSP with
Automatic Time Correction and Digital EQ

OEM Integration DSP with Automatic Time Correction and Digital EQ. 8-ch. Inputs / 4-ch. Stereo + 2 Subwoofer RCA Outputs

The FiX™ 86 is a state-of-the-art digital signal processor engineered to deliver outstanding sound from factory source units, while retaining OEM fader control.

Unlike typical OEM interface products, the FiX™ 86 automatically corrects time-delayed factory outputs prior to signal summing and EQ correction. Calibration takes just a single button press and about 30 seconds to complete, with no special equipment needed.

With a powerful 24-bit DSP processor and quad 1/3 octave equalizers onboard, complex factory signals, up to 3-way front and 2-way rear, are combined and level matched automatically into six, full-range stereo signals: Front (fader-controlled), Rear (fader-controlled) and Subwoofer (non-fading, front+rear summed) outputs.

By connecting a PC running TüN™ Software via USB, you can also access a complete suite of diagnostic panels that show the frequency response of input signals, as well as the corrected outputs. Adjustments can be made to input polarity, muting, and filtering, and new calibrations can be initiated from the PC as well. By clicking on the “TUNE” tab of the TüN™ interface, you can also access four, user-adjustable, 10-band, graphic equalizers to fine tune the output signals.

Differential-balanced inputs accept virtually any OEM analog audio signal, from low-voltage, line-level to high-power, amplified speaker-level outputs (up to 30V RMS).

Activation methods include 12-volt or Auto Turn-On (Signal/DC-Offset Sensing) to trigger a dedicated remote turn-on output for aftermarket equipment.

An optional DRC-100 or DRC-200 Digital Remote Controller (sold separately) adds Master Volume Control and/or Subwoofer Level Control from the driver’s seat.

Achieving great sound from your factory stereo has never been easier, or sounded better... Now with fader retention and subwoofer output!

General Specifications
Power Supply Type Regulated DC-DC SMPS
Input Operating Voltage 10 - 16 VDC
Standby Current Draw <1.5 mA
Operating Current Draw 0.7 A
Recommended Fuse Value 1 A
Input Channels Eight
Input Type Differential-Balanced
Input Voltage Range 250 mV - 30 V RMS
Minimum Input Voltage 10 mV RMS
Input Level Setting Fully automatic
Output Channels Six (Front/Rear/Sub Output Pairs)
Analog Output Unbalanced, stereo RCA jacks
Digital Output N/A
Output Impedance 450 Ω
S/N Ratio 96 dB (A-Weighted, referred to 4V RMS Output)
THD+N @ Rated Output 0.02% (20 Hz - 20 kHz)


Signal Processing
Audio Resolution 24 bit / 48 kHz
Number of EQ Bands 30 x 2 channels
EQ Resolution 1/3 octave (25 Hz - 20 kHz)
Remote Level Control Optional (DRC-100 or DRC-200)
Remote Level Functions Master Volume Control, Handsfree Optimization, LED Status Reporting (DRC-200 adds Subwoofer Level Control)




ADDRESS

15 Hagerty Blvd - Unit F
West Chester, PA 19382

Phone: 610-788-2226


 CONNECT WITH US
OUR BRANDS
 STORE HOURS
Typical Store hours are
Monday - Friday 
10AM - 6PM & every other
Saturday from 10AM to 3PM
but we are currently working by appointment only.
Please call or email to discus options for your project.



To book a consultation appointment with us, please click below:

Book an appointment with Tier One Motoring using SetMore